Vision Fitness Elliptical Trainer E3700HRT User Manual

i t a l l  
s t a r t s  
w i t h a  
v i s i o n  
A s s e m b l y  
G u i d e  
500 South CP Avenue  
toll free 800.335.4348  
P.O. Box 280  
Lake Mills. WI 53551  
fax 920.648.3373  
phone 920.648.4090  
©2006 Vision Fitness. All Rights Reserved. 11.06  
AG18.47PRD  
REV1  
E3700HRT  
COMMERCIAL FITNESS BIKES  
 
STEP  
3
PINK BAG  
A s s e m b l y  
G u i d e  
Feed the heart rate wires of the  
handlebar through the small hole located  
in the front of the console mast. Pull  
these wires up through the hole at the  
top of the console mast. Attach the  
handlebar to the console mast using  
four bolts (M8x20L). Tighten with the  
5mm T-shaped wrench.  
Console  
E3700HRT  
COMMERCIAL FITNESS BIKE  
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order.  
Before proceeding, find your new Fitness Bikes serial number located on the front axle tube, and enter here:  
STEP  
4
Handlebar  
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in  
your own records. Be sure to read your Owners Guide before using your new Fitness Bike.  
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12  
STEP  
3
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble  
your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws  
and bolts are in place and partially threaded in before completely tightening any ONE screw or bolt.  
STEP  
4
CONSOLE  
• Remove the four mounting bolts from  
the back of the console with the  
screwdriver. Plug in the wire harness  
and the two heart rate wires to the  
back of the console. Attach the console  
to the console mast with the four bolts  
removed earlier in this step.  
Accessory  
Tray  
STEP  
1
ORANGE BAG  
• Install the rear foot with four lock  
washers (M8), two inside bolts  
(M8x65L), and two outside bolts  
(M8x20L). Tighten with the 5mm  
T-shaped wrench.  
Remove the battery cover on the  
backside of the console. Plug in the 9-  
volt battery. Re-attach the battery cover.  
• With the screwdriver, remove the two  
bolts located half way up the console  
mast. Attach the accessory tray to the  
console mast with the two bolts.  
Wire Harness  
Rear Foot  
STEP  
Heart Rate  
Wires  
2
BLUE BAG  
Console Mast  
• Slide the console mast boot onto the  
console mast.  
• Unfold the wire harness located in  
the console mast frame bracket.  
Connect it to the wire tie coming from  
the bottom of the console mast. Pull  
the wire tie and wire harness up  
through the top of the console mast  
while simultaneously sliding the mast  
into the frame bracket.  
Console Mast  
Boot  
STEP  
1
• Secure the mast to the frame using  
six lock washers (M8) and six bolts  
(M8x15L). Tighten with the 5mm  
T-shaped wrench. Place the seventh  
bolt (M8x15L) in the rear of the frame  
bracket and tighten until snug.  
STEP  
2
Frame  
Bracket  
• Slide the console mast boot down  
and set it in place on the side cover.  
• Remove the nuts (M8) from the bottom  
of the seat. Attach the seat to the seat  
post with the nuts you just removed.  
Tighten with the 15mm wrench.  
 

Toshiba CRT Television CZ32T31 User Manual
Toshiba DVD Player SD 3990 User Manual
Toshiba DVD Player SD4300 User Manual
Toshiba Portable DVD Player SD P1900SR User Manual
Tripp Lite Network Card U244 001 R User Manual
Tripp Lite Power Supply 932645 User Manual
Tripp Lite TV Cables B015 000 User Manual
Universal Remote Control Home Theater System DMS AV TPS2000 User Manual
Viking Oven F20517 User Manual
Wayne Water Pump 352205 001 User Manual