Vision Fitness Treadmill T9350HRT User Manual

A s s e m b l y  
G u i d e  
T9250, T9350HRT AND T9450HRT  
FOLDING TREADMILLS  
 
TOOLS, HARDWARE, & PARTS INCLUDED  
8mm Allen Wrench  
5mm Allen Wrench  
Screwdriver  
PARTS BOX  
Water Bottle, Qty: 1  
Heart Rate Chest Strap, Qty: 1  
(Except T9250)  
Color-coded Hardware Bags  
Owners Guide  
Assembly Guide  
Warranty Card  
 
HARDWARE INCLUDED  
PINK BAG  
ORANGE BAG  
M8 x 20L Bolts  
Quantity: 2  
M8 x 20L Bolts  
Quantity: 4  
M8 x 50L V-Head Bolts  
Quantity: 2  
BLUE BAG  
M4 x 12L V-head Screw  
Quantity: 2  
M4 x 12L V-head Flat Screw  
Quantity: 4  
M8 x 135L Bolts  
Quantity: 4  
 
STEP  
1
ORANGE BAG  
• Fold up the right-hand console mast  
to the vertical position. Be sure not to  
pinch the data cables.  
• Insert the bolt (M8 x 50L) in the side  
and tighten with the blue-handled 5mm  
Allen Wrench.  
STEP  
1
• Insert one bolt (M8 x 20L) in the front  
and tighten with the blue-handled  
5mm Allen Wrench.  
• Repeat this on the opposite side.  
NOTE: There are no data cables on  
the left side.  
STEP  
2
BLUE BAG  
• Slide the base side covers down the  
left-hand and right-hand console  
masts.  
• Fold the treadmill to the vertical  
position.  
• Secure the right-hand base side  
cover to the base frame. Use the  
V-head screw (M4 x 12L) for the rear  
of the cover and the Flat screws  
(M4 x 12L) for the front of the cover.  
Repeat this step on the left-hand side.  
• Unfold the treadmill.  
STEP  
2
5
 
STEP  
3
PINK BAG  
• Mount the right-hand side mount  
handlebars to the console mast using  
two bolts (M8 x 135L). Repeat this on  
the left-hand side.  
• Plug in the large data cable into the  
large plug connection in the connection  
box on the right-hand side of the console.  
• Plug in the small data cable into the  
small plug connection in the  
connection box on the right-hand side  
of the console  
NOTE: Push all extra data cable into  
the console mast. Make sure not to  
pinch or cut the data cable.  
• Mount the console to the console  
masts using four bolts (M8 x 20L)  
and tighten with the blue-handled  
5mm Allen wrench.  
STEP  
3
6
 
STEP  
4
AUTO-CALIBRATION  
Once the treadmill is plugged in, you need to perform an Auto-Calibration to assure maximum performance.  
MODELS T9350HRT & T9450HRT:  
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION  
You need to access User Engineering Mode to run the Auto-Calibration. With the Safety Key in place, please  
hold down SPEED DOWN and SELECT for 5 seconds. When in the User mode, "USEr" displays in the center  
window. To access the data press the ELEVATION keys until "Auto" appears in the center window. Press Start to  
select this function.  
To begin Auto-Calibration, press START. The treadmill will run through minimum and maximum Speed and  
maximum Elevation. This will take 3-5 minutes. Let the treadmill perform this complete function before exiting the  
Engineering Mode.  
• Elevation A/D or Elevation in % appears in the left window. PWM value or Speed appears in the right  
window. "End" will appear in the center window when the Auto-Calibration is complete. When Auto-Calibration  
is complete, it will take the treadmill about 30 seconds to go to 0% Elevation and return to the start-up screen  
with “P1” showing in the Function window.  
MODEL T9250:  
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION  
• With the Safety Key in place, hold the ELEVATION UP and SPEED DOWN buttons for 5 seconds. The console  
will beep 5 times and a number will appear in the window. Shortly thereafter, EnG1” will appear in the  
window. Press the ELEVATION UP or SPEED UP to “EnG4.”  
• Press START. The treadmill will Auto-Calibration itself. It will take 3-5 minutes. When the Auto-Calibration is  
complete "END" will flash in the window. Wait 10 seconds.  
• Remove the Safety Key. Then, put the Safety Key in place to use the treadmill.  
7
 
STEP  
BELT TENSION  
5
• If the running belt slips when used,  
use the supplied 8mm Allen wrench to  
turn the left and right tension bolts  
1
clockwise /4-turn at a time until the  
belt no longer slips.  
• If the running belt is too far to the  
right side, use the supplied 8mm Allen  
wrench to turn the right tension bolt  
1
clockwise /4-turn at a time until the  
belt remains centered during use.  
If the running belt is too far to the left  
side, turn the left tension bolt  
1
clockwise /4-turn at a time until the  
belt remains centered during use.  
STEP  
5
500 South CP Avenue  
P.O. Box 280  
Lake Mills, WI 53551  
fax 1.920.648.3373  
toll free 1.800.335.4348  
phone 1.920.648.4090  
©2004 Vision Fitness. All Rights Reserved. 7.04 Part #Z92TM42C-AG  
AG18.31PRD  
REV1  
8
 

Technika Flat Panel Television LCD46 920 User Manual
Tiger Lawn Mower TWR 120 User Manual
Toastmaster Can Opener TCO2 User Manual
Toshiba Blu ray Player BDX2700KU User Manual
Toshiba Power Supply 4200FA CT User Manual
Tricity Bendix Cooktop CSI 2400 User Manual
Tunturi Treadmill J 440 User Manual
Valcom Speaker V 1060A User Manual
Verizon Network Card VZ4010 User Manual
Vivotek Digital Camera IP3112 User Manual