Vision Fitness Treadmill T9500HRT Orbo User Manual

A s s e m b l y  
G u i d e  
T9200, T9300HRT, T9500HRT, T9500HRT Ortho  
AND T9600HRT Comfort AND T9700 Series  
PLATFORM TREADMILLS  
 
TOOLS, HARDWARE, & PARTS INCLUDED  
5mm L-Shaped Wrench  
8mm Allen Wrench  
Screwdriver  
PARTS BOX  
Water Bottle, Qty: 1  
Heart Rate Chest Strap, Qty: 1  
(Except T9200)  
Color-coded Hardware Bags  
Owners Guide  
Assembly Guide  
Warranty Card  
 
HARDWARE INCLUDED  
BLUE BAG  
ORANGE BAG  
M8 x 15L Bolts  
Quantity: 4  
M8 x 20L Bolts  
Quantity: 2  
M8 x 55L Flathead Bolts  
Quantity: 4  
YELLOW BAG  
M4 x 12L Panhead Screws  
Quantity: 4  
M8 x 135L Bolts  
Quantity: 4  
 
STEP  
1
ORANGE BAG  
• Slide the rubber covers on to the left  
& right console supports, making sure  
that the lower cutout is facing inward.  
T9700-Series: Slide the data cable  
down the right console support using  
the white wire tie as a guide. Make  
sure that the data (1 large ribbon  
cable) goes through the large hole in  
the lower part of the console upright.  
T9200, T9300HRT, T9500HRT,  
T9500HRT Ortho  
&
T9600HRT  
Comfort: Slide the data cables down  
the right console support using the  
white wire tie as a guide. Make sure  
that the data cables (one small & one  
large telephone-style cable) go  
through the large hole in the lower  
part of the console upright.  
STEP  
1
• Insert the left console support into  
the console support bracket and  
secure with two bolts (M8 x 55L  
Flathead) in the side of the console  
support bracket.  
• Insert one bolt (M8 x 20L) in the  
rear of the console support bracket.  
• Tighten all three bolts with the 5mm  
Allen wrench.  
• Repeat this on the right side.  
NOTE: There are no data cables on  
the left side.  
5
 
STEP  
BLUE BAG  
2
• Mount the console to the console  
mast using four bolts (M8 x 15L) and  
tighten with the 5mm Allen wrench.  
STEP  
2
NOTE: Push all extra data cable into  
the console mast. Make sure not to  
pinch or cut the data cable.  
• Mount the right-hand side mount  
handlebar to the console mast using  
two bolts (M8 x 135L). Repeat this on  
the left-hand side.  
STEP  
3
DATA CABLES  
STEP  
3
MODELS  
T9200,  
T9300HRT,  
T9500HRT, T9500HRT Ortho, &  
T9600HRT Comfort: Plug in the small  
data cable into the small plug  
connection on the lower control  
board. Plug in the large data cable  
into the large plug connection on the  
lower control board. Slide down the  
rubber covers on the left & right  
console supports.  
MODELS T9700S, T9700HRT: Plug  
the large 20-ribbon cable into the  
20-pin connection on the lower  
control board. Slide down the rubber  
covers on the left & right console  
supports.  
• Install the motor cover making sure  
that the rubber covers are inserted into  
the motor cover. Secure the motor  
cover using the six (M4 x 12L) screws  
(see Yellow bag).  
6
 
STEP  
4
AUTO CALIBRATION  
Once the treadmill is plugged in, you need to perform an Auto-Calibration to assure maximum performance.  
MODELS T9300HRT, T9500HRT, T9500HRT Ortho, & T9600HRT Comfort:  
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION  
You need to access User Engineering Mode to run the Auto-Calibration. With the Safety Key in place, please  
hold down SPEED DOWN and SELECT for 5 seconds. When in the User mode, "USEr" displays in the center  
window. To access the data press the ELEVATION keys until "Auto" appears in the center window. Press Start to  
select this function.  
To begin Auto-Calibration, press START. The treadmill will run through minimum and maximum Speed and  
maximum Elevation. This will take 3-5 minutes. Let the treadmill perform this complete function before exiting the  
Engineering Mode.  
• Elevation A/D or Elevation in % appears in the left window. PWM value or Speed appears in the right  
window. "End" will appear in the center window when the Auto-Calibration is complete. When Auto-Calibration  
is complete, it will take the treadmill about 30 seconds to go to 0% Elevation and return to the start-up screen  
with “P1” showing in the Function window.  
MODELS T9700S & T9700HRT:  
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION  
You need to access User Engineering Mode to run the Auto-Calibration. With the Safety Key in place, please  
hold down SPEED DOWN and SELECT for 5 seconds. When in the User mode, "User Mode" appears in the  
alphanumeric window. To access the data press the ELEVATION keys until "Auto-Cal" appears. Press Start to select  
this function.  
To begin Auto-Calibration, press START. The treadmill will run through minimum and maximum Speed and  
maximum Elevation. This will take 3-5 minutes. Let the treadmill perform this complete function before exiting the  
Engineering Mode.  
• Elevation A/D or Elevation in % appears in the left window. PWM value or Speed appears in the right  
window. "Cal Passed" will appear in the alphanumeric window when the Auto-Calibration is complete. The  
treadmill will come to a complete stop and return to the start-up screen in the alphanumeric window.  
MODEL T9200:  
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION  
• With the Safety Key in place, hold the Elevation Up and Speed Down buttons for 5 seconds. The console will  
beep 5 times and a number will appear in the window. Shortly thereafter, EnG1 will appear in the window. Press  
the Elevation Up or Speed Up to “EnG4”.  
• Press Start. The treadmill will calibrate itself. It will take 3-5 minutes. When the Auto-Calibration is complete  
"END" will flash in the window. Wait 10 seconds.  
• Remove the Safety Key. Then, put the Safety Key in place to use the treadmill.  
7
 
STEP  
5
BELT TENSION  
• If the running belt slips when used,  
use the supplied 8mm Allen wrench to  
turn the left and right tension bolts  
1
clockwise /4-turn at a time until the  
belt no longer slips.  
• If the running belt is too far to the  
right side, use the supplied 8mm Allen  
wrench to turn the right tension bolt  
1
clockwise /4-turn at a time until the  
belt remains centered during use.  
If the running belt is too far to the left  
side, turn the left tension bolt  
1
clockwise /4-turn at a time until the  
belt remains centered during use.  
STEP  
5
500 South CP Avenue  
P.O. Box 280  
Lake Mills, WI 53551  
fax 1.920.648.3373  
toll free 1.800.335.4348  
phone 1.920.648.4090  
©2004 Vision Fitness. All Rights Reserved. 7.04 Part #Z92TM49C-AG  
AG18.12PRD  
REV6  
8
 

Tascam VCR CC 222MKIV User Manual
Technicolor Thomson Stereo System CS140 User Manual
Technics Portable Speaker SB CD301 User Manual
Trane Air Conditioner GAF2A0A24S21SA User Manual
Uniden Cordless Telephone EXT 1365 User Manual
United States Stove Stove 5500 5500XL User Manual
Universal Remote Control Universal Remote UR5U 9000L User Manual
Video Products Computer Hardware SM 2X2 HDMI LC User Manual
ViewSonic Intercom System EXES 2000 User Manual
Vizio Weather Radio TWRS I User Manual