Vision Fitness Treadmill T9800 Series User Manual

STEP  
5
AUTO-CALIBRATION  
DO NOT STAND ON THE BELT WHEN PERFORMING AUTO-CALIBRATION  
You need to access User Engineering Mode to run the auto-calibration. With the safety key in place, please hold  
down SPEED DOWN and ENTER for 5 seconds. When in the User mode, “USER ENG MODE” appears in the  
alphanumeric window. To access the data press the ELEVATION keys until “AUTO-CALIBRATION” appears.  
To begin auto-calibration, press ENTER. The treadmill will run through minimum and maximum speed and  
maximum incline. This will take 3-5 minutes. Let the treadmill perform this complete function before exiting the  
Engineering Mode.  
Elevation A/D appears in the left window. PWM value appears in the dot matrix window, and speed appears in  
the right window. “CALIBRATION PASSED” will appear in the alphanumeric window when the auto-calibration is  
complete. The treadmill will come to a complete stop and return to the start-up screen in the alphanumeric window.  
A s s e m b l y  
G u i d e  
500 South CP Avenue  
toll free 800.335.4348  
P.O. Box 280  
Lake Mills, WI 53551  
fax 920.648.3373  
T9800 Series  
phone 920.648.4090  
TREADMILLS  
©2007 Vision Fitness. All Rights Reserved. 5.07  
AG18.39PRD  
REV7  
 
STEP  
3
PINK BAG  
A s s e m b l y  
G u i d e  
• Insert the handlebar cover onto the  
handlebar. Insert the right handlebar  
by holding the handlebar sideways  
toward the treadmill and inserting the  
top into the console. Rotate the  
handlebar into the bracket located on  
the console mast. Fasten with a bolt  
(M5x12L), and a bolt (M6x15L socket  
head) & an arc washer (6.5x13x1T)  
into the two holes of the console plas-  
tic, and a bolt (M8x15L flat head) into  
the hole in the handlebar. Fasten a bolt  
(M6x15L socket head) and a flat washer  
(6.5x19x2T) into the hole in the handle-  
bar on the console mast. Do not fully  
tighten the bolts.  
T9800 Series  
TREADMILLS  
To avoid possible damage to this Platform Treadmill, please follow these assembly steps in the correct  
order. Before proceeding though, find your new Platform Treadmills 2 serial numbers, located on the  
underside of the main frame, and on the bottom of the console, and enter here:  
STEP  
2
• Slide the handlebar cover over the  
bracket and secure with  
(M6x15L socket head) and  
washer (6.5x19x2T). Do not fully  
tighten the bolt.  
a
bolt  
flat  
Frame Serial Number  
Console Serial Number  
a
Refer to these numbers when calling for service, and also enter these serial numbers on your Warranty  
Card and in your own records. Be sure to read your Owners Guide before using your new Platform Treadmill.  
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12  
STEP  
3
• Repeat on the left side.  
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Platform  
Treadmill, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts  
are in place and partially threaded in before completely tightening any ONE bolt.  
• Fully tighten the console and  
handlebar bolts.  
STEP  
4
MOTOR COVER  
TV Power Cable  
STEP  
1
ORANGE BAG  
• Place the motor cover back on the  
frame and fasten with 6 screws.  
Coaxial Cable  
Remove motor cover screws and  
• Attach the power cord to the treadmill.  
take off the motor cover.  
STEP  
4
• Plug the power cord into the power  
outlet.  
• Insert the right console mast to the  
right console mast bracket. First, fasten  
the inside of the console mast to the  
console mast bracket by securing four  
bolts (M8x15L socket head) and four  
washers (8.2x19x2T). Fully tighten the  
bolts. Second, fasten the two bolts  
(M10x20L button head) and two  
washers (10.2x19x2T) on the front of  
the console mast and fully tighten.  
STEP  
5
6
AUTO-CALIBRATION  
TV BRACKET WIRING  
Please refer to back cover for this  
procedure, then return to Step 6.  
• Repeat on the left side  
STEP  
1
STEP  
BELT TENSION  
STEP  
2
BLUE BAG  
• If the running belt slips when used,  
run the treadmill at 2.0 mph and use  
the supplied 8mm Allen wrench to turn  
Tie the ribbon data cable, TV  
power cable, and coaxial cable to  
the cable wire tie on the top of the  
right console mast. Feed the cables  
down the console mast and through the  
hole at the lower part of the console  
mast. Remove protective plastic cover.  
Push any remaining cable into the  
console mast.  
the left and right tension bolts clockwise  
1
/4-turn at  
a
time until the belt no  
longer slips.  
• If the running belt is too far to the  
right side, run the treadmill at 2.0 mph  
and use the supplied 8mm Allen  
wrench to turn the right tension bolt  
1
clockwise /4-turn at a time until the  
• Mount the console onto the left and  
right console masts using four bolts  
(M8x15L socket head) and four washers  
(8.2x19x2T). Do not fully tighten.  
belt remains centered during use.  
If the running belt is too far to the left  
side, run the treadmill at 2.0 mph and  
turn the left tension bolt clockwise  
STEP  
6
1
Take the wire tie off the cables. Plug  
the large 20-pin ribbon connector into  
the 20-pin connector on the lower  
control board. Attach the two grounding  
wire connectors to the two grounding  
wires located in the motor pan near  
the front of the frame. Connect the TV  
power cable to the TV power connector  
and coaxial cable to the coaxial  
cable connector; both located on the  
inside of the motor compartment at the  
front of the treadmill.  
/4-turn at a time until the belt remains  
centered during use.  
 

Techno Source Video Games 21101 User Manual
Toastmaster Juicer 1108 User Manual
Toshiba Automobile Parts LF434 User Manual
Toshiba DVD Player SD 2800U User Manual
Tote Vision Flat Panel Television LCD 1212TW User Manual
Tricity Bendix Cooktop SIE533 User Manual
Vector Mobility Scooter 167662 R0700A User Manual
ViewSonic Computer Monitor VA1928WM User Manual
Vizio Flat Panel Television E401IA2 User Manual
Vulcan Hart Range 7800 User Manual